eobdtool

eobdtool
EOBDTool

2017年6月27日星期二

€18 BMW B800 Airbag Reset Tool turn off E36 SRS light DIY

Cheap €18 BMW Airbag ResetTool B800 turn off BMW E36 airbag light OK, easy for BMW DIY Repair!
Tips: For old E36 only has round 20pin OBD port, just need a €4.5  BMW 20pin to OBD2 16pin Connector.

How to reset BMW airbag light easily by BMW B800?
Connect BMW B800 with car via the OBD port. (If it's old BMW without a 16 pin connector, you can use the above 20pin to 16pin converter adapter.)
Simply press the ENTER button to start airbag reset!
Every press, BMW B800 screen will show different codes. What does they mean?
The "FA" on screen means BMW B800 is connected successfully and ready to work.
The "09" and "02" separately means the different BMW airbag error codes. (You can look for BMW B800 manual to check the description)
When the screen show "--" code that means BMW airbag reset is done!
In this way, BMW B800 turn off BMW airbag light easily! No more airbag light flash on the dashboard.

Also take out BMW B800 PCB for your checking:

2017年6月8日星期四

How to Use BMW ENET E-sys to Flash F25 NBT

This is how to flash BMW F25 NBT with E-Sys ENET cable.

One way to get bmw esys enet is- to download BMW E-sys with luck, and build an ENET cable. This is the DIY guide: http://blog.eobdtool.co.uk/how-to-build-enet-cable-for-f-series-coding/

The other way is- to spend a little bit more money to buy a working cable, then this is a site that has been confirmed working:

You will need to put the car on a commercial grade charger, good for 50 amps minimum, as you cannot run the motor while flashing.

Here are the basic steps:

Go to Comfort Mode => TAL-Calculating
- Read and Save FA
- Activate FA
- Read and Save SVT Actual as SVT_ist
- Create an SVT Target
Under KIS/SVT Target Calculation Strategy, select Complete Flash
Select I-Step (shipm.) to match your original I-Level as read and shown in VCM I-Step (Shipment)
I-Step (target.) will be unselectable as it is fixed based on current PSdZData I-Level
Do a KIS/SVT Target Calculation and Save as SVT_soll
- Do a TAL Calculation and Save as SVT_tal

Go to Expert Mode => TAL-Processing
Load TAL (SVT_tal)
Load SVT Target (SVT_soll)
Select "Read FA" button.
Check radio button for "read VIN out of FA"
On ECU Tab, uncheck let top box in column "All" (All checked boxes should toggle to unchecked)
On ID Base Row for Kombi, make check boxes in blFlash, swDeploy, cdDeploy, and ibaDeploy columns.
Press Check software availability
Press Start and it will proceed with processing TAL to flash Kombi with new firmware.



The last- a good place with lots of great write-ups of BMW F series coding: http://bmw-f-coding.blogspot.com/

2017年6月7日星期三

(06.2017) Free Download BMW ISTA 4.05.32 Standalone for ICOM

Below are free download links for BMW ISTA-D 4.05.32 Standalone + BMW ISTA-D license! Enjoy at your own risk and hope it helps!

You are going to download:
ISTA-D 4.05.32 Standalone Version
FASTA & HW check is off
Included last firmware for BMW ICOM & ICOM NEXT
And added BMW ISTA License.


BMW ISTA 4.05.32 Standalone Download:
Link 1
Or link 2
BMW ISTA 4.05.32 license Download:
No pass!!! No dead links!!!
Thank to Spider80...
Note:
This new ISTA 4.05.32 is still with unknown security, eobdtool.co.uk engineers can't assure you 100% working!
So which BMW ISTA Crack is tested100% OK with ICOM clone?
Here you go:
BMW ISTA HDD WIN7
Compatible with ICOM A2, A3, NEXT
Not connected 9000 days remaining!

BMW ISTA Interfaces recommended:

What functions can you do using ISTA with above tools?
--Module (ECU) errors reading and clearing
--Gearbox (transmission) and engine adaptations erasing
--Fuel injectors control, correction amount real time viewing, injector registering
--Engine mountings testing
--Mass air flow (MAF) testing and registering. Whole air system testing
--EGR system control and testing
--Turbocharger and related components control and testing
--Diesel particulate filter regeneration (DPF)
--Battery replacement
--Oil change and service interval reset
--Wiring diagrams live data, repair instructions, technical documents etc
And much more other functions...

BMW Rheingold ISTA 4.05.23 Update Information (06.2017)
Works with ALL BMW E and F series 1995-2017
Suitable for BMW Motorcycle
--Language: ENG, GER, FR, RU, OTHER
--Ultimate Ediabas/ISTA+ voltage control
--Hardware check disabled -can use the program on the slower laptops.
--ISTA contains all the functions required for programming vehicles of the F, G and I series and for Motorrad models with vehicle electrical system 2020 (BN2020).
--With Technical Information (TIS) and Wiring Diagram (WDS).
--Ediabas and all necessary tools included.
--Included components (32-Bit & 64-Bit)
--Included :
ISTA User Manual EN,DE, IT,PL,RU,TR,CZ,ES,FR,JP,KR,NL,SE
NET Framework 4.6 + Updates
Java Runtime Environment 8
DirectX 9.0c Extra files
General runtime files
Microsoft Visual C++ Runtimes (v2005 - v2015)
Microsoft Visual J# 2.0 SE
Microsoft Silverlight 5
Adobe Flash Player (Opera, FireFox, Internet Explorer)
Shockwave Player 12 (Internet Explorer Plugin
Ediabas
--BMW ISPI ICOM-FW 03-15-00
--BMW ISPI ICOM-Next-FW 03-15-00

BMW ISTA-D 4.05.32 Standalone Operating System Requirements:
Windows 7 (32-bit or 64-bit)
Windows 8 (32-bit or 64-bit)
Windows 8.1 (32-bit or 64-bit)
Windows 10 (32-bit or 64-bit)

BMW ISTA-D 4.05.32 Standalone Hardware Requirements:
Processor (CPU): Intel Pentium 2.0 GHz, Core Duo 2.0 GHz or better
Memory (RAM): 3 GB or more

Hard drive (HDD): 22 GB free space on disk

Rheingold/ Esys delete “Lifetime” FSC

Is it possible to delete “Lifetime” FSC?
Yes, it’s possible. There must be a way to delete so called lifetime maps FSC code from NBT and return to normal behaviour of updates.

Just E-sys to generate a working code for any other region.
Insert map of other region, enter code, you don’t even have to wait for upload to finish.
Insert maps from region you use and enter code for that particular map update.
CIC/NBT in general can only store single code.


For f-series, just read fsd with esys check en of FSC, lifetime is AD7Q Also upgrade index is FF
For Eseries, fstool.

If someone doesn’t have functional fstool (for E-series), it’s even easier to download data03 file from /mnt/hbdebug/. Code is the last 20 characters of the file, and if the last 4 are AD7Q it is the lifetime code.
And the easiest way to change it with the tool is directly in Rheingold.

This method work. I removed the lifetime fsc code.
But the cic doesn’t update, usb and dvd.

2017年6月5日星期一

BMW E46 DME Update by WinKFP Guide+ Import Daten files Q&A

This blog is a step-by-step guide for BMW E46 DME Update DIY by WinKFP. First to download BMW INPA EDIABASWinKFP BMW Coding Tool NCS Expert all programs you need!

How to update BMW DME Module using WinKFP easily?
Tool needed:
Before you start, you should firstly import the daten files cirrectly! Or the update will be fail.
Check below case:
I have run into an issue after installing WinKFP 5.3.1
I have INPA running ok, import the SGDA (.IPO files), ECU (.PRG files) and assembly line data. After choosing "Comfort Mode" -> "Update ZUSB", there is nothing on the "ECU family". It's empty.
Do I import the files incorrectly? Any solution please?

Solution 1. You can use WinKFP Tool to import the daten files. Here is a guide for your checking.
Solution 2. You can also import daten files via BMW coding tool. It's tested working.

Steps to Update BMW DME using WinKFP:
Connect BMW E46 car with laptop via BMW ICOM or BMW INPA K+DCAN.
Open WinKFP.
Click F1 button "Comfort mode".
Click F3 button "Update ZUSB" and you get a box displaying ECU families.
pull down the drop-down list to choose the ECU family (MDS42 for MS42, MDS43 for MS43, MDS451 for MS45.1, etc.), click OK.
Click F4 button "Enter VIN" and input car VIN number.
Click "Done", which goes back a screen.
Click F3 button "Prog ZB-Update", and you should get a box that displays your current ECU version and suggests an update version.
Click "Yes" and you get another box asking permission to program ECU.
Click OK and the update begins.
It takes about 10-15 minutes to complete for MS42/43, 45 minutes for MS45.1.
At the end it tells you that the programming was OK.
Reset adaptation values using INPA or PA Soft after it is done.

2017年5月23日星期二

2017 BMW Dr. Gini B020 Free Download+ Install with EDIABAS

Here you can free download the useful BMW Diagnostic Program BMW Dr. Gini B020 2017 version! And BMW Dr. Gini installation guide also shared as below!

Free download BMW Dr. Gini B014+ B020+ EDIABAS 7.3.0:
Note:
1. In order to get Dr.Gini Program work, a program called Ediabas must be properly installed.
2. BMW cars produced before 2003 are not supported yet.
3. Dr.Gini Program need these communication interfaces:

How to install 2017 BMW Dr. Gini Diagnostic Program?
Step 1: Before install Dr.Gini, first you need to install EDIABAS.
In the EDIABAS folder, run the EDIABAS _7.3.0.msi file to install the EDIABAS program.
It is recommended that you do not change any settings during installation.

Step 2: Unpack the "Setup Dr.Gini B014 EN.zip" and run the program to install Dr.Gini.
At the end of the installation, the menu that you want to run the program is checked, but since the setup is not completed yet, it is unchecked and the installation is completed.

Step 3: After extracting the compressed files in the ECU folder, copy them to the ECU folder where EDIABAS program is installed.
If you did not change the settings during installation, this is the C:\ EDIABAS\ ECU folder.

Step 4: Copy the EDIABAS.INI file located in the "INTERFACES" folder→ ENET Ediabas.INI folder and overwrite the C: \ EDIABAS \ BIN folder, as Dr.Gini will be connected by the ENET cable.
You need to copy the api32.dll file in the "API32.DLL" folder to the folder below for each operating system.
For Windows 7/8 / 8.1 / 10 64-bit operating systems:
C:\Windows\SysWOW64
For Windows 7/8 / 8.1 / 10 32-bit operating systems:
C:\Windows\System32

Step 5(The final step): Copy the Gini_B020.exe file to the C: \ EDIABAS \ BIN folder.
Sometimes, Gini_B020.exe is recognized as a malicious program and may be removed from an anti-virus program. If you feel that this process is unstable, you can just delete this file.

OK. Now BMW Dr. Gini installation is complete!
Connect your car with BMW Dr. Gini via BMW ICOM, ICOM NEXT, INPA K+DCAN Cable or ENET Cable. And it's ready to use!
Turn on car ignition and run the Dr.Gini.exe located in the C:\EDIABAS\BIN folder.
Click the "Identification" button at the bottom of the screen. Then the software will directly connect to vehicle.

2017年5月22日星期一

Free download BMW ISTA 4.05.23 Standalone+ SQLiteDBs 05.2017

05.2017 BMW ISTA Rheingold update notice!
Here you can free download BMW ISTA-D 4.05.23 Standalone+ SQLiteDBs for BMW ICOM A2, ICOM A3 and ICOM NEXT, etc. Works with ALL BMW E and F series 1995-2017!

Download Rheingold ISTA+ Standalone V4.05.23:
ISTA 4.05.23 Standalone
Link 1
Or Link 2

Download ISTA 4.05.23 SQLiteDBs FULL (11.77GB)
Link 1
Or Link 2
Note: Enjoy at your own risk. Hope it helps!
Is there any newer version of BMW ISTA working and safe 100% tested?

BMW ISTA 4.05.23 Compatible Interface ALL here

BMW ISTA 4.05.23 Software Installation Guide for reference
1. Install .Net Framework 4.5.2 version and up, from Microsoft
2. Install Java.
3. Download and install Microsoft Visual C++ 2010/2013 Redistributable Package x86/x64 from Microsoft for your language in Windows.
For computer x86:
- vs90_piaredist
- vcredist_x86_2005
- vcredist_x86_2008
- vcredist_x86_2010
- vcredist_x86_2012
- vcredist_x86_2013
- vcredist_x86_2015
For computer x64:
- vs90_piaredist
- vcredist_x64_2005
- vcredist_x64_2008
- vcredist_x64_2010
- vcredist_x64_2012
- vcredist_x64_2013
- vcredist_x64_2015
Note:
If the system is x64, vcredist must install x86 and x64, otherwise not start Rheingold.
4. Install Ediabas 7.3
5. Unblock archive if necessary. It is important to not skip this step! Unblock file, uncheck Attributes - Read-only. Then unzip.
6. Unzip to any directory, for example: C:\Rheingold, D:\Rheingold, E:\Rheingold..., C:\Program Files\, C:\Program Files (x86) - this folder for 64bit computers. You can run from USB stick too.
7. Unzip and copy SQLiteDBs in Rheingold\SQLiteDBs\
8. Add additional languages if necessary in SQLiteDBs
9. Start RCleaner. Run as administrator.
10. Apply ISTA-D and SQLiteDBs Reg Fix bit for your system from the Tools folder.
11. Start Rheingold (...\Rheingold\TesterGUI\bin\Release\ISTAGUI.exe) Run as administrator.
12. Enter the license key from the license.txt, if ask.
13. Enter 1 in the field of ISIS, ignore the error.

BMW ISTA 4.05.23 Software Operating Systems
Windows 7 (32-bit or 64-bit)
Windows 8 (32-bit or 64-bit)
Windows 8.1 (32-bit or 64-bit)
Windows 10 (32-bit or 64-bit)

BMW ISTA 4.05.23 Hardware Requirements
Processor (CPU): Intel Pentium 2.0 GHz, Core Duo 2.0 GHz or better
Memory (RAM): 3 GB or more
Hard drive (HDD): 22 GB free space on disk